Gas Hot Air Furnace Services
Gas hot air furnace repair, tune-ups and installation, with fast diagnosis on ignition and airflow problems.
24/7
Emergency service
Same Day
Most repairs
Licensed
& fully insured
Upfront
Pricing, no surprises
Call (877) 717-8383 for 24 hour service.
Our Services
How a Gas Furnace Works and Where It Fails
A gas valve delivers fuel to the burner, an igniter lights it, a heat exchanger transfers that heat into the air stream, and a blower pushes warm air through the ductwork. When any one of those pieces fails, the symptoms are usually specific enough to narrow down the cause quickly.
We work on furnaces from every major manufacturer and every age, and we carry parts on the truck that cover the most common failure points on either, including igniters, flame sensors, capacitors and gas valves.
A technician traces the ignition sequence step by step, from thermostat call through gas valve, igniter and flame sensor, since a furnace that shuts itself down mid-cycle is almost always reacting correctly to a fault somewhere in that chain rather than malfunctioning on its own.
What Our Gas Furnace Tune-Up Covers
An annual tune-up before heating season is the cheapest insurance against a mid-winter breakdown.
- Burner and igniter cleaning
- Flame sensor cleaning and testing
- Blower and capacitor testing
- Gas pressure verification
- Heat exchanger inspection
- Venting and flue check
Ignition and Flame Sensor Problems
Standing pilot furnaces fail when the pilot will not stay lit, usually because the thermocouple has weakened and can no longer hold the gas valve open. Furnaces with electronic ignition fail differently, most often a cracked hot surface igniter, a bad control board, or a dirty flame sensor that shuts the gas valve back off within seconds of ignition.
A flame sensor works by detecting a tiny electrical current through the flame itself, and even a thin layer of oxidation on its surface is enough to break that signal, which is why cleaning it is one of the most common and effective repairs we make.
Blower Motors and Heat Exchangers
A blower motor that hums without starting or fails outright can cause the furnace to overheat internally and shut down on its high limit switch. We check the heat exchanger carefully on any older unit, since cracking or corrosion there can let combustion gases leak into the supply air, which is a safety issue and not just a repair item.
Airflow, Ductwork and When to Replace
A restrictive or clogged filter is the single most common reason a healthy furnace runs constantly and still cannot keep a house comfortable, so we check filter condition and duct static pressure on every visit.
When a furnace needs a heat exchanger, has an aging blower motor, or keeps generating repair calls, replacement with a new high efficiency gas furnace is usually the smarter long term spend. We size new equipment to the house and existing ductwork rather than defaulting to whatever unit is on the truck, since an oversized furnace short cycles and an undersized one runs constantly without keeping up.
What Affects Furnace Repair and Replacement Cost
The part that failed drives most repair pricing, since a flame sensor cleaning costs far less than a control board or blower motor replacement. On installation jobs, ductwork condition and any needed venting changes are the biggest cost variables, along with the efficiency rating of the new furnace chosen.
Frequently Asked Questions
Why does my gas furnace click but not light?+
Clicking without ignition usually means the igniter is cracked, the flame sensor is dirty, or the gas valve is not opening. It can also mean the control board has detected a safety fault and is refusing to send gas. A technician can test each component in sequence and usually isolate the cause within minutes, restoring heat the same visit in most cases.
How long does a gas hot air furnace usually last?+
Most gas furnaces run reliably for around 15 to 20 years with regular maintenance, though install quality and servicing history affect that number. Once a furnace needs a heat exchanger or its major components fail in the same season, replacement usually makes more financial sense than continued repair, especially on units near the end of that range.
Why is one room colder than the rest with the same furnace?+
Uneven heat almost always comes down to ductwork, whether that is an undersized branch run, a disconnected duct, or a closed or blocked register. It is rarely the furnace itself unless the blower is significantly underperforming. A duct inspection usually pins down the exact cause, and balancing dampers can sometimes correct it without any duct replacement.
Do I need a permit to replace a gas furnace?+
Yes, furnace replacement in New Jersey typically requires a permit and inspection, especially when gas piping or venting is being altered. We handle the permit and schedule the inspection as part of the installation, so you do not have to coordinate that separately with the municipality yourself.
How often should the filter be changed on a gas furnace?+
A standard filter should be checked monthly and typically changed every 1 to 3 months depending on filter type and household dust. A clogged filter restricts airflow and can trigger safety shutoffs or overheat the heat exchanger over time. We can recommend the right filter type and thickness during a service visit.
Contact Us Today!
Tell us what your gas furnace is doing and a technician will get it diagnosed with a price before any repair starts.
Call Jersey City Plumbing Heating & Cooling at (877) 717-8383 any hour for gas furnace service.